Art of Stone

Greystar Headquarters: Marble Floor Restoration

At Greystar’s corporate headquarters in Charleston, South Carolina, we restored the marble flooring throughout the main entrance and lobby as part of a larger renovation. The work covered approximately 920 square feet of natural stone, laid in large-format slabs measuring about 35 × 50 inches.

The project came to us through the renovation contractor. After our technical director, Ivan Andreev, inspected the floor, assessed its condition, and measured the work area, we prepared a restoration proposal for Greystar. The goal was not to replace the stone, but to address wear, renew the joints, and achieve a consistent, professionally finished surface.

A good restoration starts with understanding which areas actually need deeper work, and which only need their finish refreshed.

The Challenger

The Challenge

The floor was generally sound, but the wear was not evenly distributed. Scratches and scuffing were more visible near the garage entrance and elevators, where constant foot traffic had affected the marble. Across the wider lobby, most of the stone needed a lighter finishing treatment rather than intensive grinding.

The joints presented a second problem. The existing cementitious grout had darkened, collected dirt and cracked in places. Because the slabs were unusually large, the condition and color of the joints strongly influenced the overall appearance of the floor.

The Result

Our Response

We treated the stone according to its condition, rather than using one aggressive process everywhere.Worn areas received more intensive abrasive refinishing, while the larger field was repolished to bring the overall finish together.

We also removed the deteriorated grout, cleaned and refilled the joints, and applied a penetrating protective treatment after the floor dried. The completed project was inspected before being handed back to the client.

Location: 465 Meeting Street, Charleston, SC

Property: Greystar Corporate Headquarters

Stone: Natural marble

Area: Approx. 920 sq. ft.

Schedule: 3 working days

On-site team: 3 specialists

The Restoration Process

Working with large-format marble in a high-traffic commercial lobby required a coordinated sequence: restore the joints first, refine the stone second, and seal the dry surfaces last.

The Challenger

Day 1

Joint preparation and regrouting

We carefully removed the old cement grout from between the marble slabs. The open joints were vacuumed and washed to clear dust, residue, and embedded contamination before new grout was installed in the color specified by the client’s designer.

The Result

Day 2

Targeted refinishing and polishing

Ivan selected different abrasive treatments for different areas of the floor. Heavier wear near the garage and elevators called for more cutting action; elsewhere, the marble was given a gentler finishing polish. All treated areas were then brought to a coordinated final appearance.

 

The Challenger

Day 3

Drying, sealing and handover

Because wet polishing introduces moisture, we allowed the floor to dry before applying a professional penetrating sealer to the stone and grout. The treatment helps reduce absorption and makes routine care easier. Our team then carried out a final inspection.

 

The Result

A practical decision about the grout

We discussed two approaches with the client: a professional cement-based grout similar in type to the original, and an epoxy grout that we recommended for its stronger resistance to contamination and chemical exposure in a busy lobby.

Greystar elected to use cement-based grout, with the final joint color determined by its designer. We completed the work to the approved specification, while adjusting our stone-restoration methods to the actual condition of each area.

Protection without overpromising

A penetrating sealer helps limit absorption and simplify maintenance. It does not make marble completely stain-proof or prevent chemical etching. The finish still benefits from appropriate cleaning and routine care.

The Result

Over three working days, our three-person team renewed the damaged joints and refinished the marble across the entrance and lobby. The more worn sections received focused attention, while the larger floor area was polished to a more uniform appearance.

 

The work preserved the existing large-format marble and gave the building an updated floor finish without unnecessary replacement. This project reflects the kind of material-specific, carefully sequenced restoration we bring to commercial spaces.

Select the fields to be shown. Others will be hidden. Drag and drop to rearrange the order.
  • Image
  • SKU
  • Rating
  • Price
  • Stock
  • Availability
  • Add to cart
  • Description
  • Content
  • Weight
  • Dimensions
  • Additional information
Click outside to hide the comparison bar
Compare